Zhone DNE4500-S Especificações Página 1

1 ETHX-2214-DS3 and ETHX-2224-DS3 EtherXtend DS3 Ethernet Access Device Installation Instructions Document Number ETH3-A2-ZN10-10 Issue 2 - August

10 Single DS3 Connection A single line connection can be established between a single port Subscriber unit and either a single port or dual port ET

11 Connecting the Ethernet Lines The 10/100BaseT Ethernet ports can auto-negotiate speed and duplex mode in accordance with the remote equipment to

12 LED Indicators Table 2. DS3 LEDs LED State Indication Additional Information Flashing Green* DS3 connection is established and active Traff

13 Table 3. Ethernet LEDs LED State Indication Additional Information Pulsing Green Standard operation Traffic is flowing without any probl

14 Web Interface The network extender’s integral web management lets you configure and monitor the network extender using a standard web browser.

15 5. Write down the current IP Address and Subnet Mask in the Internet Protocol (TCP/IP) Properties dialog box. When you are done using web manag

16 From this screen you can: Click on . . . To configure . . . Management Config. IP Address, Subnet Mask, Default Gateway, In-band Managemen

17 Establishing an Static ARP Table Entry for a Subscriber Unit The Subscriber unit’s DS3 ports will not respond to an ARP request containing the

18 Configuring Provider or Subscriber Modes To reconfigure a unit from Provider (factory default) to Subscriber mode, open the web management home

19 Command Line Interface The network extender can be managed with a Command Line Interface (CLI) through either a direct PC to COM (Communication)

2 Software and Firmware License Agreement ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE SOFTWARE AN

20 Launching the Terminal Emulation Program Launch a terminal emulation program on your PC and configure the program settings. The terminal emulat

21 Resetting the Network Extender to Factory Defaults The network extender supports a reset process that may be used to delete the current configur

22 Connector Pin Assignments Ethernet Pin Assignments Table 4. Ethernet Pin Assignments Pin Function Pin 1 Rx+ Pin 2 Rx– Pin 3 Tx+ Pin 4 no

23 Specifications Specifications are subject to change without notice. Table 6. Specifications Criteria Specification Bandwidth/Distance Up to 4

24 Safety Notices This product is compliant with the Standards for Safety of Information Technology Equipment (ITE) defined in ANSI/UL 60950-1, Fir

25  Verizon NEBS Requirements by Location SIT.NEBS.RQS.NPI.2005.031, Issued Nov 14, 2005 (non-Carrier requirements only)  AT&T

26 Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2.

27 Copyright 2008 Zhone Technologies, Inc. Printed in U.S.A.

28 **** ETH3-A2-ZN10-10 **** **** 830-01728-02 ***

3 5. Except for the Product warranty contained in the manual, the Software is provided “AS IS” and in its present state and condition and Zhone

4 Introduction to ETHX-2214-DS3 and ETHX-2224-DS3 The EtherXtend 2200 Series of DS3 Ethernet Access Devices (EADs) allows Carriers, ISPs and PTTs t

5 Provider vs Subscriber Units The EtherXtend 2200 DS3 units can be operated in either a Provider or Subscriber mode. A Subscriber unit is always c

6 Provider and Subscriber Unit Defaults The following table highlights the differences between Provider and Subscriber units. Table 1. Unit Def

7 Powering Up the Network Extender The DC power terminal block on the network extender has five terminals: two positive, two negative, and one with

8 Power Connection – AC Power 1. The AC power supply is shipped with the power terminal strip already attached. No AC power supply other than th

9 Connecting the DS3 Lines The ETHX-2214-DS3 device supports a single, unframed DS3 facility while the ETHX-2224-DS3 device supports up two (2) unf